Heath Zenith ac-29 User Manual download pdf

Installation Instructions and Drill Template.

Read and Save these Instructions.

• The non-electric chime mounts directly

through the door and will accommodate

door thicknesses of 3/4" to 2".

• The chime is equipped with a viewer.

LOCATING THE DOOR CHIME

1. Mount the chime in the center of the door

approximately 4

feet to 5 feet above

the ﬂoor. Note: Be sure there are no

obstructions on the inside of the door

to interfere with the chime’s baseplate.

2. Using the template provided, mark the

location of the mounting holes parallel

to the edge of the door (see Figure 1).

Note: It is important that the holes are

parallel to the edge of the door for proper

operation of the chime.

3. Drill two 1" holes parallel to edge of

door.

4. Drill three pilot holes using a 1/16" drill

bit.

PUSH BUTTON ASSEMBLY

See Figure 1 for push button assembly.

Note: If push button assembly is located

in an area that is exposed to rain, caulk

around the 1” holes before attaching push

button to door.

Figure 1 - Attaching Push Button Assembly to Door

ATTACHING PUSH BUTTON

ASSEMBLY

1. Remove metal trim screw, metal trim,

name card holder, and name card from

push button assembly to locate mounting

holes (see Figure 1).

2. Insert viewer and push button shaft into

predrilled until push button assembly is

ﬂush against door face. Attach using the

three mounting screws provided (see

Figure 1).

3. Print or type name and address on name

card (provided). Place card in holder

with printing visible through front of card

holder.

4. Place metal trim over push button as-

sembly and name card holder. Secure

trim with trim screw (see Figure 1).

1/16" Pilot Hole

1" Viewer Hole

1" Shaft Hole

Viewer

Push Button Shaft

Push Button Assembly

Mounting Screw

Name Card

Name Card Holder

Metal Trim

Door Edge

Trim Screw

Two-Note

Non-Electric Door

Chime – With Viewer

MODEL: AC-29

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - Chime – With Viewer

Page 2 - ATTACHING CHIME COVER

10 598-1225-01INSTALLATION DU CARILLON1. Mettez l’ensemble carillon en place sur la tige du bouton-poussoir et sur l’oculaire (consultez la Figure 2)

Page 3 - TECHNICAL SERVICE

11598-1225-01ACE® se réserve le droit de mettre ﬁn à la production de ses produits ou d’en modiﬁer les spéciﬁcations à tout moment, et elle n’est pas

Page 4 - 4 598-1225-01

12 598-1225-01ORIFICESD’ORIENTATION1/16 po (3 ENDROITS)3/16 poORIFICE DELA TIGE DUBOUTON-POUSSOIR –DIAMÈTRE 1 poINSTALLER À4 1/2 - 5 pi DU BASDE LA PO

Page 5 - - con visor

2 598-1225-01MOUNTING CHIME ASSEMBLY1. Position chime assembly over push button shaft and viewer (see Figure 2).2. Verify chime assembly is para

Page 6

3598-1225-01ONE YEAR LIMITED WARRANTYThis is a "Limited Warranty" which gives you speciﬁc legal rights. You may also have other rights which

Page 7 - SERVICIO TÉCNICO

4 598-1225-011/16" PILOT HOLES(3 LOCATIONS)3/16"PUSH BUTTONSHAFT HOLE1" DIA.MOUNT4 1/2 - 5 ft.ABOVE BOTTOMOF DOOR(TOP)MODEL 29MOUNTING

Page 8 - 8 598-1225-01

5598-1225-01Campana no eléctrica de dos-notas para puerta - con visorInstrucciones de instalación y plantilla de perforación.Lea y guarde estas in

Page 9 - Carillon à deux notes

6 598-1225-01MONTAJE DEL CONJUNTO CAMPANA1. Coloque el conjunto campana sobre el eje del pulsador y sobre el visor (vea la ﬁgura 2).2. Veriﬁque que

Page 10 - Partie A

7598-1225-01GARANTÍA LIMITADA A 1 AÑOEsta es una “Garantía Limitada” que le da a Ud. derechos legales especíﬁcos. Usted puede también tener otros dere

Page 11

8 598-1225-01ORIFICIOS GUÍAS DE1/16 PULGADAS(3 UBICACIONES)3/16pulgadasORIFICIO DE1 PULGADA DEDIÁMETRO PARAEL EJE DELPULSADORINSTALE DE 4 1/2 - 5PIES

Page 12 - MODÉLE 29

9598-1225-01Carillon à deux notes non électrique avec oculaireDirectives et gabarit d’installation.Lisez et conservez ces directives.• Le carillon no